Aquaponic Solar Water Heater

Filed under: Videos |


Quick video showing the layout of a DIY solar water heater I whipped up to (hopefully) keep the water in my aquaponic system warm during the chilly Arizona w…

Have something to add? Please consider leaving a comment, or if you want to stay updated you can subscribe to the RSS feed to have future articles delivered to your feed reader.

13 Responses to Aquaponic Solar Water Heater

  1. Randall Kerstetter
    April 29, 2014 at 9:42 pm
    Reply

  2. New video upload giving a quick rundown of a solar water heater I made to
    keep outdoor fish tank water warm during the chilly Arizona winter.
    #Aquaponics #Solarthermal

    Randall Kerstetter
    April 29, 2014 at 10:39 pm
    Reply

  3. What temperatures were you running before you installed the solar heater?

    POVadventure
    April 29, 2014 at 11:37 pm
    Reply

  4. Great idea, Randall! Super simple and seems like it works very well. This
    could have some great overlap in other applications too like off grid
    living. Nice work!

    Bright Agrotech
    April 30, 2014 at 12:16 am
    Reply

  5. found you on bkudell’s channel. i, too, am in arizona…Lake Havasu
    City…hoping us Arizonians could show our systems (share info) since we
    have to deal with such drastic heat in the summers. Thank you for your
    videos

    toddac1
    April 30, 2014 at 12:27 am
    Reply

  6. Thank you! Later in the winter I removed the 1/2″ irrigation tubing and
    made a revision using 3/4″ PVC pipes painted black and oriented vertically,
    to make use of the thermosiphon effect. Water flows in one pipe at the top,
    down one side, into a manifold on the bottom, then up through 12 pipes into
    a top manifold, and finally out the opposite side it entered from. Flow
    rate and temperature change both seemed to improve when compared to the
    model shown here.

    Randall Kerstetter
    April 30, 2014 at 1:14 am
    Reply

  7. To many places to leak. Should have used it in roll form with only chance
    of 2 fittings to fail.

    Rednicks Fabshop
    April 30, 2014 at 1:40 am
    Reply

  8. Hi man, appreciate your work and sharing! One word though, you REALLY want
    to insulate your pipes, especially (but not only) the hot return one
    -otherwise, there’s too much loses to the environment, first water cools
    down while traveling to the heater, then heats up (but starts from already
    lower temp than if the feed pipe was insulated), than heated water returns
    and cools down again, on its way back. Insulation is crucial. Keep up!

    michbushi
    April 30, 2014 at 2:03 am
    Reply

  9. That was my original thought as well, and to be honest, filling it up for
    the first time I had my fingers crossed. Not too long ago there was a
    failure in the system due to a low-flow condition which caused excessive
    temperatures. Oddly enough, not one of the barbed or compression fittings
    for the 1/2″ tubing failed. A blister formed in the tubing itself, which
    eventually popped, and the slip-to-male-NPT PVC adapter partially melted.
    By the time I found it, steam was coming out of the exit.

    Randall Kerstetter
    April 30, 2014 at 2:23 am
    Reply

  10. Rest assured, if this weren’t just a quick experimental setup, I would’ve
    definitely picked up some insulation for the piping, as well as the AP
    system itself. Notice the growbed, fish tank, and sump are all uninsulated
    as well. Stay tuned to see a larger system that’s in the works! Considering
    the flow rate and inlet water temperature, standard PVC should be plenty
    safe, but I will note that CPVC and/or PEX are recommended for hot water
    transfer. Legitimate concern though, good call!

    Randall Kerstetter
    April 30, 2014 at 2:32 am
    Reply

  11. Second thought: have you checked by chance the temps of the piping inside
    the panel? I wonder if it doesn’t get too hot there – so some nasties could
    be released from PVC in there? Appreciate your opinion/experience!

    michbushi
    April 30, 2014 at 3:01 am
    Reply

  12. New video upload giving a quick rundown of a solar water heater I made to
    keep outdoor fish tank water warm during the chilly Arizona winter.
    #Aquaponics #Solarthermal

    Noah Plaza
    April 30, 2014 at 3:54 am
    Reply

  13. Razvan Popescu
    April 30, 2014 at 4:37 am
    Reply

Leave a Reply to Randall Kerstetter Cancel reply

Your email address will not be published. Required fields are marked *